Search results

I think the temperature sensor or wires are not working properly, my car doesn't seem to pull right, mechanically the engine is new with non-cat camshafts (which are more agressive) and lighnted crankshaft and ported heads it should make a lot more power but the car feels weak, its even hard to...

It seems I have the 2 connectors type but one of them was eaten by my dog (while the exhaust manifold was in the courtyard). I have to say, I knew the lambda trick for a while but my car just works a lot better with the lambda connected, the engine has a smoother sound too.

Another question, the lambda has only one wire ? because where the wire connects to the harness there is another connector which remains empty(same connector as injectors or temperature sensor) is it possible that my lambda is missing one connector?

So basically if I remove it its all good? Or do I have to put the wire like this so I have 98 ron mapping?

Hey! Can you post the photo with the wire please?:D

The car seems a lot torquier with this AFM than the other 2 without flap (the 3 digit number is 955 by the way). I'm trying to make my cat 33, non-cat. The question is, if I remove the yellow relay and do an ecu reset will it run the non-cat mapping?

I haven't written anything here for a while, the car has done 2500 km since I've finished it (1 month). There are things I still have to adjust but overall I'm happy with it. I will post some photos soon. I'm curios about one thing though, I have 3 AFM's and one of them is a bit different, they...

Well now that I think about it, the springs are exactly the same on each side, so there must be something in "mirror", in this case the supports. I would really like if any of you could take a look on your car and tell me if its ok XD

I really have no ******* ideea, should it look like that? :-s

Thanks a lot! I have a question, looking at photos 4 and 5 , doesn't it seem strange to you the position of the spring/shock absorber on one of the sides?

So I've finished front and rear brakes and full suspensions, I was lucky enough to have a summer rain so I washed the 1 year old painted car for the first time (it was really dusty after 1 year). Those are my upgraded brakes by the way ...

Yea I thought so :D Thanks for the nice words, I just hope ill have more to show pretty soon, the more it starts to shape up the less patience I have to finish the project :D

Thanks for the warm welcome! Yea well, I'm working my *** off with this car haha, I hope the next weekend I finish the front end too, brakes and shocks and stuff, hard work but it looks nice in the photos haha !

So, long time since I've written here. I've found the side trims (except drivers door one). The car used to drive well on 16 inch and pilot exhalto 2 but at that time it had rubbish bushes and bad springs/shocks setup so I can give you a better review after the resto finishes. I'm pretty lazy to...

Hey mate! Nice to be part of this family! I hope more and more members will join from other forums also!

The news are pretty bad, the side trims are not to be found new I've been informed. Could anyone help me with this matter?

I've found some rust that the painter/rust guy left in the windshield area so I've had to fix it myself, not much rust but definitely had to be fixed. While doing so I've damaged the paint on the A pillar (very very little) so I might repaint the A pillar on the left side. I've received the...

Glad you like it, thanks for the support, keeps me going (feels like forever since I last drove it, 2 years ago)

Hahaha the car is actually supported by a barrel covered in many rubber car mats(on the other side, next photo) !!! This part of the restoration was done by the painter who also is a metal man, welder whatever, he is pretty good at it too :P

I hope this wont be considered spam :) Here are the photos almost up to date with the restoration. LE: Seems I've messed up a bit adding some photos twice.